Kinetic Engineering Home     |     About Us     |     Contact Us     |     Site Map
rule
Products
rule

Heat Exchangers

Shell & Tube Heat Exchangers

Brazed Plate Heat Exchangers

Plate and Frame Heat Exchangers

TEMA Exchangers

Air & Gas After Coolers

Double Pipe Heat Exchangers

Multitube/Hairpin Heat Exchangers

Custom Process Heat Exchangers

Spiral Heat Exchangers

Double Tube Heat Exchangers

Standard Stainless Steel Air Coolers

Fin Fan Heat Exchangers

Plate Fin Heat Exchangers

Welded Plate Heat Exchangers

Plate Shell Heat Exchangers

Wide Gap Welded Heat Exchangers

Fired Process Heaters

Helical Coil/Serpentine Coil Heaters

Thermal Fluid Heaters

Convection Process Liquid Heaters

rule
Elanco - Spiral Heat Exchangers

The "A" type is the conventional SHE. It has the basic rolled core with removable heads on both sides. Both sides are in spiral flow, true counter flow. The channels are separated with pins to keep the channel spacing. The pinned spacing and removable heads allow for mechanical cleaning and inspection of both sides of the SHE. These are used for services that are fouling on both sides of the exchanger, and require cleaning often.

A special class of pin free units are manufactured for sewage treatment plants; and Elanco Inc has the most competitive sludge to sludge interchanger for thermal treatment of sewage available.

The "B" type uses the same basic core as the "A" type, but has only one removable head. Again both sides in spiral - true counter flow patterns. It is used then only one fluid is fouling. The other side is most often the service side with cooling tower water or steam. Elanco has done a lot of work with cooling tower water, and has developed velocity - temperature - pressure drop standards for SHE use when mechanical cleaning is not an option. By using high velocity in the channels, the cooling tower water will not foul the prime surface by more than f+.0005, for stainless steel. Annual descaling returns unit to new and clean, and is accomplished with a chemical descaler. The "B" type is substantially less costly to produce than an "A" type.

The "C" type SHE begins with the same basic core as an "A" type, the unit is all welded and has no removable heads. Both fluids need to be relatively clean. There are two separate reasons for a "C" type construction. One, it is the least costly SHE, it has all the advantages of a spiral heat exchanger, true counter flow, can handle solids, small, compact, etc, and it less costly than one with removable heads. The second reason is Elanco has developed a super strength all welded version that can handle cycling and huge temperature shock. The all welded unit is very useful for high and low temperatures where gaskets become a problem. These are applications that SHE explicitly avoided before. The "C" has been used for high temperature gas to gas, for cooling heat transfer oils with liquid nitrogen, and for heating freezing xylene with steam. So advantageous is the "C" type to temperature shock, it has replaced U-Tube S&T units that failed due to the tube bundle rotating in the shell from the thermal stress.

The "D" type SHE is a hybrid, utilized both axial and spiral flow patterns. This design is extensively used in partial, vacuum and atmospheric knockback condensers. Most applications have the vapors entering the top of a vertical SHE axially, which exposes the flow to a large condensing surface area. The reduced flow than enters a spiral path that will subcool and separate the vapors/non-condensable, from the liquids. Elanco Inc has developed new advanced design codes for partial condensers that allow these units to smaller. The new codes have made the premier suppliers of low pressure and partial condensers.

The "E" type SHE has one side in spiral flow and on side in axial flow. This arrangement is used for condensing with no subcooling, and for very large volume flow rate, (usually a gas), which are on the axial side. The advantage is the ability to expose the flow to large surface areas, with little pressure loss. The flows are in cross flow, not counter flow. The axial side has fouling similar to a shell and tube heat exchanger, and the spiral side must be all welded construction.

Applications

  • Slurries
    • PVC Production
    • Waste Water Treatment
    • Textile and Laundry Plants
    • Mineral Mining & Production
    • High & Low Temperature
  • Exhaust Coolers
    • Gas to Gas, (up to 1650 F)
    • Liquid Nitrogen Cooled HTO
    • Fuel Cells & Reformat
    • High Viscous
  • Column Bottoms Coolers
    • Fatty Acid Coolers
    • Resin/Plastic Feed Heaters
    • Up to 20,000 Centipoises
    • Condensers
  • Partial Condensers
    • Column Top Condensers
    • Knockback Condensers
    • Vacuum Condensers
Manufacturers
rule
rule

Heat Transfer Equipment

Standard Xchange

Heat Exchanger Design

Elanco

Fin-X

Super Radiator Coils

Premium Process Equipment

rule

Fired Process Heaters

Heatec

rule

Need More Information?

Bob Hedrick
bob@kineticengineering.com

Andy (Andres) Diaz
andy@kineticengineering.com

Ken Stone
ken@kineticengineering.com



rule
© 2008 Kinetic Engineering Corporation Home     |     About Us    |     Heat Transfer Equipment    |     Fired Process Heaters     |     Contact UsWeb Site Design by Multi-FX LLC